What is the representation of the width and length of the straight edge of the advertising engraving machine?

W1: The width of the front end of the cutting edge. The common width is 2MM, 1.5MM. Generally, it is slightly smaller when it is set. Because the front end is convenient for chip removal, the side edge is repaired, so the actual width is slightly smaller.

H1: The length of the cutting edge of the tool, the height of the material to be cut should be lower than the length of the blade. Generally, the H1 is set to about 5 mm.

What is the difference between the advertising engraving machine and the knife? The bottom knife is more than the straight knife, and the lower two blades can drill down like a drill bit. The advertising engraving machine straight knife can not be in principle.

Advertising engraving machine straight knife loading and unloading?

1. When cleaning, use a gasoline or WD40 cleaning agent to clean the chuck and pressure cap.

2. Put the chuck into the pressure cap, otherwise the cutter is not easy to install. If the chuck is not clamped in the pressure cap, the chuck will be caught in the motor shaft when the knife is unloaded.

3. Before clamping, pay attention to whether the chuck matches the selected tool, otherwise the tool cannot be tightened.

4. When clamping the tool, the part of the tool that protrudes out of the chuck should not be too long, otherwise it will easily generate vibration during the machining process, which will affect the processing quality of the workpiece surface.

5. When changing the tool, it must ensure that the spindle speed is zero, that is, the tool can be dismantled when the spindle is stopped, otherwise serious personal injury accidents may occur.

6. If you use the presser foot to engrave, you must use a vacuum cleaner to clean the dust on the presser foot and the spindle, and then clamp the tool.

7. In the process of screwing up the cap upwards, be sure to press the cap on the positive rotor thread, first screw it in place with no effort.

8. When unloading the knife, use an air gun to clean the dust on the pressure cap and the rotor shaft before unloading the knife.

Advertising engraving machine straight knife depth setting? When setting the path, there is engraving depth, and it can also be set on the Z axis when the knife is fixed.

The advertising engraving machine goes straight down? Look at the size of the purchased knife and spring clips, or look at the degree of wear of the spring clips.

Advertising engraving machine straight knife broken knife processing? When the knife is broken, click “Stop”. After the knife is changed, the Z-axis coordinate is reset and cleared. Enter the current line segment number in the "Specific location" via "Advanced Start" under the "Operation" menu (according to the situation, some convenience overlap)

Does the advertising engraving machine use interrupted power processing? Move the machine back to the mark position before processing, and clear it. Click Simulation to see what the current line number is. The remaining steps are the same as above.

Advertising engraving machine tips?

1. In the actual processing, the relationship between machining effect and machining efficiency should be fully considered, and the coarse knife, fine knife and three-dimensional engraving can be flexibly applied. Large-area graphic area engraving uses large tools for processing, and small-area graphic areas or The effect of the small tool should be used for fine machining, and the setting of the overlap rate of the tool is also important.

2. Select the processing method according to the processing result requirements-----two-dimensional engraving, three-dimensional engraving or cutting. If pattern engraving is performed, two-dimensional or three-dimensional engraving is selected, and the generated processing path is the engraving path. If you are cutting and machining the wall surface of the sand table model, select "Cutting Word" and the generated path is the cutting path.

3. According to the requirements of processing effect, the path generation method is selected. The two-dimensional path is suitable for plane engraving. The processing effect does not have a strong three-dimensional effect, and the processing fineness is inversely proportional to the processing depth. The three-dimensional path has a "clear angle" engraving action, the processing effect has a strong three-dimensional effect, the processing pattern is fine, the processing fineness is directly related to the fineness of the pattern and the accuracy of the tool parameters, and the processing depth only affects the three-dimensional and does not affect the fineness of the processing. The degree, the greater the processing depth, the stronger the stereoscopic effect.

4. According to the fineness of processing and the texture of the material, choose the engraving processing path form----horizontal milling bottom, vertical milling bottom, forward 45 degree milling bottom, reverse 45 degree milling bottom. These engraving paths produce high processing precision. The processing surface is smooth. The circular path has a fast processing speed and high efficiency, but the processing effect is inferior to others.

5. Engraving tool selection, pay attention to the influence of cutting edge angle and blade width on machining accuracy and progress. If the cutting edge angle and blade width are large, the machining speed is fast, but the machining pattern is not fine, the cutting edge angle and blade width are Small processing speed is slow, but the graphics are fine and the durability of the tool is relatively poor.